Fitsipika momba ny fandidiana fitaovana famonoana matetika

1. Tsy maintsy voaofana sy mahafeno fepetra ireo mpandraharaha amin’ny fitaovana famonoana afo avo lenta vao afaka miasa.

2. Rehefa manomboka ny fitaovana milina dia velomy aloha ny rafitra famatsian-drano, avy eo dia velomy ny famatsiana herinaratra ny fitaovana milina, avereno ny boltsan’ny filamenta voalohany sy ny filamenta faharoa, avereno ny voltase avo, ary amboary ny Output malefaka bokotra mba hahatonga ny malefaka hahatratra ny miasa malefaka malefaka. (Famonoana: Miverina amin’ny aotra ny famantarana mivoaka amin’ny tsindry avo, ary miverina mihidy indray ny mifamadika amin’izay. Mihemotra 30 minitra ny rafitra famatsian-drano mba hikatona)

3. Install the heating sensor without connecting to the power supply. The connection between the pressure-reducing ring and the sensor should be in good contact. If there is oxide, use emery cloth or other methods to remove it. Adjust the gap and height between the sensor and the workpiece, and keep it parallel to the side plate. (that is, adjust the position in the X, Y, Z directions, and record the data)

4. Ny fitaovana fampangatsiahana ny fitaovana famonoana matetika dia matetika ny rano sy ny fifantohana amin’ny ranon-tsakafo, ary ny mari-pana amin’ny fitaovana famonoana dia latsaky ny 50 °C; ho an’ny workpieces sasany izay tsy mahafeno ny fepetra takiana, dia avela hanitsy araka ny tokony ho izy ny fifantohana amin’ny ranon-javatra mamono, fa tsy maintsy azo antoka fa mahafeno fepetra ny hamafin’ny ary tsy misy triatra famonoana.

5. Alohan’ny famokarana, mila ho reraka ny vongan-dranomandry mamono, ary tsy misy foam fotsy mibaribary amin’ny ranon-tsavony.

6. Ny halalin’ny sosona mahery vaika mahomby amin’ny fitaovana famonoana matetika dia tokony ho santionany sy refesina araka ny fepetra takiana amin’ny fitsapana sy ny fenitra mifandraika amin’ny karatra fizotry ny fitsaboana hafanana mba hahafeno ny fepetra ara-teknika.

7. Ny mpandraharaha dia mila manitsy ny dingana masontsivana araka ny fepetra takian’ny ny dingana, sensor samy hafa, ary ny fomba famonoana hafa (fixed-point na mitohy). Ny ampahany tsirairay amin’ny ampahany dia mila vonoina 1-2 alohan’ny famokarana. Aorian’ny fitsapana dia tsy misy triatra famonoana matetika, ary ny hamafin’ny sy ny halalin’ny sosona mafy dia mahafeno fepetra alohan’ny famokarana faobe.

8. Mandritra ny fizotran’ny famokarana, ny mpandraharaha dia tsy maintsy mandinika ny fiovaovan’ny voltase amin’ny fitaovana milina, ny mari-pana, ny faritra mafana ary ny fiovan’ny toerana vokatry ny toerana sy ny elanelana misy eo amin’ny workpiece sy ny sensor. Ny fiovan’ny fahafahan’ny fampangatsiahana vokatry ny fivilian’ny sodina famafazana dia tokony ahitsy amin’ny fotoana rehetra raha ilaina.

9. Ny ampahany vonoina avo lenta dia tokony ho tezitra ara-potoana, amin’ny ankapobeny ao anatin’ny 2 ora aorian’ny famonoana. Ho an’ny vy karbaona, vy firaka ary vokatra misy hateviny samihafa miaraka amin’ny votoatin’ny karbônina ≥ 0.50%, dia tsy maintsy ampidirina ao anatin’ny 1.5 ora izy ireo.

10. Workpieces that need to be reworked should be induction normalized before rework to prevent cracks caused by re-quenching. The workpieces are only allowed to be reworked once.

11. During the production process, the operator should conduct no less than three hardness tests (before, during, and at the end of the workpiece).

12. When an abnormal state occurs during the operation, the operating power should be turned off immediately, and the workshop supervisor should be reported to the workshop supervisor for adjustment or maintenance.

13. The operating site should be kept clean, dry and free of water, and there should be dry insulating rubber on the operating pedal to ensure the safety of the operator.